Elantas PDG Sterling® E300-20 Single-Component Thixotropic Thermopoxy Epoxy Resin, 10 lb/1 gal, MFR ID PDGE3002010LB
- MFR #:117646
- EIS #:PDGE3002010LB
- MFR #:117646
- EIS #:PDGE3002010LB
Available to Order
Min Qty:1
|Qty Increment:1
Elantas PDG Sterling® E300-20 Single-Component Thixotropic Thermopoxy Epoxy Resin, Epoxy Base Type, 1.2774 g/cm3 (77 °F (25 °C)) Density, 1500 V/Mil (ASTM D149 - 4 Mil), 1300 V/Mil (ASTM D149 - 4 Mil After 24 hr in Water ) Dielectric Strength, >94 °C (ASTM D93) Flash Point, 16 hr At 150 °C/302 °F Full Cure Time, 8 - 15 min At 150 °C (302 °F) Gel Time, 90 Shore D At 25 °C/77 °F Hardness, 180000 - 260000 CP At 2 rpm 25 °C/77 °F, 50000 - 70000 CP At 20 rpm 25 °C/77 °F Viscosity. - Sterling® E 300-20 thixo is a single-component, heat-cured, epoxy bonding resin.
$34.87 / US pound
Min Qty:1
|Qty Increment:1
Elantas PDG Sterling® E300-20 Single-Component Thixotropic Thermopoxy Epoxy Resin, Epoxy Base Type, 1.2774 g/cm3 (77 °F (25 °C)) Density, 1500 V/Mil (ASTM D149 - 4 Mil), 1300 V/Mil (ASTM D149 - 4 Mil After 24 hr in Water ) Dielectric Strength, >94 °C (ASTM D93) Flash Point, 16 hr At 150 °C/302 °F Full Cure Time, 8 - 15 min At 150 °C (302 °F) Gel Time, 90 Shore D At 25 °C/77 °F Hardness, 180000 - 260000 CP At 2 rpm 25 °C/77 °F, 50000 - 70000 CP At 20 rpm 25 °C/77 °F Viscosity. - Sterling® E 300-20 thixo is a single-component, heat-cured, epoxy bonding resin.
- Attributes
- Features
- Applications
- Documents
Attributes
General Information
Item NameThixotropic Thermopoxy Epoxy Resin
Trade NameSterling®
SeriesSterling® E300-20
General Features
Net Weight10.4 - 10.8 lb/gal
Shelf Life3 Months
TypeSingle-Component
Design & Construction
Base TypeEpoxy
FormLiquid
Performance Details
Full Cure Time16 hr at 150 °C/302 °F
Gel Time8 min
Technical Details
Flash Point94 °C
Chemical Properties
Viscosity180000 cP
Electrical Properties
Dielectric Strength1500 V/mil
Physical Properties
Container Size10 lb
Hardness90 Shore D at 25 °C/77 °F
Features
- Outstanding bond strength
- Good chemical resistance
- No catalyst required
- Thixotropic for minimal run-off
- Thermal ratings up to class 180
- Mix thoroughly before use, warm resin to 30-40 °C / 86-104 °F, apply with stiff brush, spatula or notched spreader application methods
- Store below 25 °C / 77 °F in a dry controlled environment out of direct sunlight
- 8 - 12 Mils film build
- 150 °C heat deflection temperature
- 1.0 x 10^12 Ohm-cm at ASTM D257 - 25 °C / 77 °F, 2.0 x 10^11 Ohm-cm at ASTM D257 - 100 °C / 212 °F volume resistivity
- 72 Pounds at 25 °C / 77 °F, 30 Pounds at 150 °C / 302 °F helical coil bond strength (ASTM D2519 over MW 35)
- Secondary insulation
- Gel Time: 8 - 15 min at 150 °C (302 °F)
- Container Size: 10 lb/1 gal
- Dielectric Strength: 1500 V/Mil (ASTM D149 - 4 Mil), 1300 V/Mil (ASTM D149 - 4 Mil After 24 hr in Water )
- Flash Point: >94 °C (ASTM D93)
- Viscosity: 180000 - 260000 CP at 2 rpm 25 °C/77 °F, 50000 - 70000 CP at 20 rpm 25 °C/77 °F
- Density: 1.2774 g/cm3 (77 °F (25 °C))
- Gel Time: 8 - 15 min
- Viscosity: 180000 - 260000 cP
Applications
- Wet-Winding of Rotating or Stationary Field Coils, Impregnation, Bonding and Sealing of Electrical and Mechanical Components