Elantas PDG Sterling® E300 Single-Component Thixotropic Epoxy Resin
- MFR #:Sterling® E300
- EIS #:PH21-Sterling E300
- MFR #:Sterling® E300
- EIS #:PH21-Sterling E300
Elantas PDG Sterling® E300 Single-Component Thixotropic Epoxy Resin, Epoxy Base Type, 1500 V/Mil (ASTM D149 - 4 Mil), 1300 V/Mil (ASTM D149 - 4 Mil After 24 hr in Water ) Dielectric Strength, >94 °C (ASTM D93) Flash Point, 16 hr At 150 °C/302 °F Full Cure Time, 8 - 15 min At 150 °C (302 °F) Gel Time, 90 Shore D At 25 °C/77 °F Hardness, 900 - 1700 CP At 25 °C (77 °F), 20 rpm Viscosity. - Sterling® E 300 thixo is a single-component, heat-cured, epoxy bonding resin.
$32.53
- $33.88
Select from the options below
Elantas PDG Sterling® E300 Single-Component Thixotropic Epoxy Resin, Epoxy Base Type, 1500 V/Mil (ASTM D149 - 4 Mil), 1300 V/Mil (ASTM D149 - 4 Mil After 24 hr in Water ) Dielectric Strength, >94 °C (ASTM D93) Flash Point, 16 hr At 150 °C/302 °F Full Cure Time, 8 - 15 min At 150 °C (302 °F) Gel Time, 90 Shore D At 25 °C/77 °F Hardness, 900 - 1700 CP At 25 °C (77 °F), 20 rpm Viscosity. - Sterling® E 300 thixo is a single-component, heat-cured, epoxy bonding resin.
Product Options
Showing 1 out of 1 options
 | Container Size: 50 lb | EIS Part #: PDGE30050LB | $ / US pound |
- Attributes
- Features
- Applications
- Documents
Attributes
General Information
Item NameThixotropic Epoxy Resin
Trade NameSterling®
SeriesSterling® E300
General Features
Net Weight11.7 - 12.1 lb/gal
Shelf Life3 Months
TypeSingle-Component
Design & Construction
Base TypeEpoxy
Performance Details
Full Cure Time16 hr at 150 °C/302 °F
Gel Time8 min
Technical Details
Flash Point94 °C
Chemical Properties
Viscosity900 cP
Electrical Properties
Dielectric Strength1500 V/mil
Physical Properties
Hardness90 Shore D at 25 °C/77 °F
Features
- Outstanding bond strength
- Good chemical resistance
- No catalyst required
- Thixotropic for minimal run-off
- Thermal ratings up to class 180
- Mix thoroughly before use, warm resin to 30-40 °C / 86-104 °F, apply with stiff brush, spatula or notched spreader application methods
- Store below 25 °C / 77 °F in a dry controlled environment out of direct sunlight
- 150 °C heat deflection temperature
- 1.0 x 10^12 Ohm-cm at ASTM D257 - 25 °C / 77 °F, 2.0 x 10^11 Ohm-cm at ASTM D257 - 100 °C / 212 °F volume resistivity
- 72 Pounds at 25 °C / 77 °F, 30 Pounds at 150 °C / 302 °F helical coil bond strength (ASTM D2519 over MW 35)
- Secondary insulation
- Gel Time: 8 - 15 min at 150 °C (302 °F)
- Dielectric Strength: 1500 V/Mil (ASTM D149 - 4 Mil), 1300 V/Mil (ASTM D149 - 4 Mil After 24 hr in Water )
- Flash Point: >94 °C (ASTM D93)
- Viscosity: 900 - 1700 CP at 25 °C/77 °F, 20 rpm
- Gel Time: 8 - 15 min
- Viscosity: 900 - 1700 cP
Applications
- Wet-Winding of Rotating or Stationary Field Coils, Impregnation, Bonding and Sealing of Electrical and Mechanical Components