Elantas PDG Epoxylite® E234 Two-Component Epoxy Impregnating Resin
- MFR #:Epoxylite® E234
- EIS #:PH21-Epoxylite E234
- MFR #:Epoxylite® E234
- EIS #:PH21-Epoxylite E234
Elantas PDG Epoxylite® E234 Two-Component Epoxy Impregnating Resin, Epoxy Base Type, Room Temperature Cure Type, 1.1450 g/cm3 (68 °F (20 °C)) Density, 1200 V/Mil At 25 °C/77 °F - 3 Mil Dielectric Strength, >94 °C (ASTM D93) Flash Point, 16 hr At 60 °C/140 °F Full Cure Time, 15 - 25 min At 25 °C/77 °F (250 g) Gel Time, 87 Shore D Hardness, 100 (Parts By Weight) Resin, 20 (Parts By Weight) 22.3 (Parts By volume) Hardener Mixing Ratio, 1000 - 2000 CP At 25 °C/77 °F Viscosity - Part-A, 100 - 500 CP At 25 °C/77 °F Viscosity - Part-B. - Epoxylite® E 234 epoxy is a two-component, low temperature curing, 100%-solids resin system, secondary insulation.
$133.89
- $237.09
Select from the options below
Elantas PDG Epoxylite® E234 Two-Component Epoxy Impregnating Resin, Epoxy Base Type, Room Temperature Cure Type, 1.1450 g/cm3 (68 °F (20 °C)) Density, 1200 V/Mil At 25 °C/77 °F - 3 Mil Dielectric Strength, >94 °C (ASTM D93) Flash Point, 16 hr At 60 °C/140 °F Full Cure Time, 15 - 25 min At 25 °C/77 °F (250 g) Gel Time, 87 Shore D Hardness, 100 (Parts By Weight) Resin, 20 (Parts By Weight) 22.3 (Parts By volume) Hardener Mixing Ratio, 1000 - 2000 CP At 25 °C/77 °F Viscosity - Part-A, 100 - 500 CP At 25 °C/77 °F Viscosity - Part-B. - Epoxylite® E 234 epoxy is a two-component, low temperature curing, 100%-solids resin system, secondary insulation.
Product Options
Showing 2 out of 2 options
 | Container Size: 2 lb | EIS Part #: EPO2342LB | $ / each | |
| Container Size: 1 lb | EIS Part #: EPO2341LB | $ / each |
- Attributes
- Features
- Applications
- Documents
Attributes
General Information
Item NameEpoxy Impregnating Resin
Trade NameEpoxylite®
SeriesEpoxylite® E234
General Features
Net Weight9.4 - 9.8 lb/gal
Shelf Life12 Months
TypeTwo-Component
Design & Construction
Base TypeEpoxy
Cure TypeRoom Temperature
FormLiquid
Performance Details
Full Cure Time16 hr at 60 °C/140 °F
Gel Time15 min
Technical Details
Flash Point94 °C
Chemical Properties
Mixing Ratio100 (Parts By Weight), 100 (Parts By Volume)
Viscosity800 cP
Viscosity - Part-A1000 cP
Viscosity - Part-B100 cP
Electrical Properties
Dielectric Strength1200 V/mil
Physical Properties
Hardness87 Shore D
Features
- Excellent penetration in trickle application
- High bond strength
- Chemical and moisture resistant
- Fast cure with low heat
- Ideal for appliance motors and other high-speed rotating devices
- Trickle application method
- Store below 25 °C / 77 °F in a dry controlled environment out of direct sunlight
- 26 Pounds at 25 °C / 77 °F, 2 Pounds at 150 °C / 302 °F helical coil bond strength (ASTM D2519 over MW 35)
- 0.2% (24 hours at 25 °C / 77 °F) water absorption
- 8.0 x 10^14 Ohm-cm (ASTM D257 - 25 °C / 77 °F) volume resistivity
- 3.7 at 1 kHz - 25 °C / 77 °F dielectric constant
- 0.02 at 1 kHz - 25 °C / 77 °F dissipation factor
- Flash Point: >94 °C (ASTM D93)
- Viscosity: 800 - 1800 CP at 25 °C/77 °F
- Density: 1.1450 g/cm3 (68 °F (20 °C))
- Viscosity - Part-B: 100 - 500 CP at 25 °C/77 °F
- Gel Time: 15 - 25 min
- Viscosity: 800 - 1800 cP
- Viscosity - Part-A: 1000 - 2000 cP
- Viscosity - Part-B: 100 - 500 cP
Applications
- Impregnation of Motor and Transformer Windings Including High-Speed Armatures