text.skipToContent text.skipToNavigation

Varnish / Resin

The finest in insulating varnishes and impregnating resins ensure your electric motors, generators, transformers and sensors will function properly and reliably. From environmental protection (moisture and dust) to added strength, varnish and resin support proper motor function and help prevent motor system failure.

  • 1(current)
  • 2
  • 3
Displaying 1 - 21 of 455 products found
  • Elantas PDG 80IP-545M Annealing Coreplate, 50 lb/5 gal, Red

    ID: 80IP545M50LB
    Mfr ID: 80IP545M50LB
    Sterling 80IP-545M red annealing coreplate was designed as a water reducible electrical insulating coating for application to electrical sheet steel which, after cutting, is stamped and then annealed to relieve cutting stresses. After the annealing operation the coating is a good separator and retains its electrical insulating properties.

     

  • 102348-ASH Ashland® Thinner, 36 lb/5 gal

    ID: 102348-ASH
    Mfr ID: 102348-ASH
    Ashland® Thinner, Liquid Form.

     

  • Von Roll/John C Dolph Dolphon® CB-1128-B Two-Part Flexible Motor Compound

    Multiple item options available
    Mfr ID: Dolphon® CB-1128-B
    Von Roll/John C Dolph Dolphon® CB-1128-B Two-Part Flexible Motor Compound, Room Temperature Cure Type, 8.8 - 9.0 lb/gal At 77 deg F (25 deg C) Density, 665 V/Mil Dielectric Strength, 2 - 4 hr At 77 deg F Full Cure Time, 45 Shore A At 70 deg F Hardness, 100:6 By Weight Mixing Ratio, 130 deg C Temperature Rating, 1260 psi Tensile Strength, 12.2 x 10^-4 Cal/sec/cm^2/deg C/cm Thermal Conductivity, 100000 cps At 80 deg F, 10 rpm Viscosity.

     

  • Von Roll/John C Dolph Dolphon® CC-1103 Solventless Resin, 55 gal

    ID: DOLCC110355G
    Mfr ID: DOLCC110355G
    Filled solventless polyester resin, this product features qualities such as 24 lbs. bond strength at 150 deg F on helical coils, similar to CC-1105. This product has film build of 1.4 - 1.7 Mil and increased thermal conductivity.

     

  • Von Roll/John C Dolph EB-43 Air-Drying Varnish, 1 gal, Black

    ID: DOLEB43FBG
    Mfr ID: DOLEB43FBG
    Von Roll/John C Dolph EB-43 Air-Drying Varnish.

     

  • Elantas PDG Elan-Plus™ BS-307 Diluent

    Multiple item options available
    Mfr ID: Elan-Plus™ BS-307
    Elantas PDG Elan-Plus™ BS-307 Diluent. Products are filled and sold by weight and may contain less than the nominal volume of the container.

     

  • Elantas PDG Epoxylite® E6107 Two-Component High-Temperature Impregnating Epoxy Resin

    Multiple item options available
    Mfr ID: Epoxylite® E6107
    Elantas PDG Epoxylite® E6107 Two-Component, High-Temperature Impregnating Epoxy Resin, Epoxy Base Type, 1.2040 g/cm3 (68 deg F (20 deg C)) Density, 480 V/Mil Dielectric Strength, 143 deg C (ASTM D93 Part A Resin), > 94 deg C (ASTM D93 Part B Catalyst) Flash Point, 6 - 8 hr At 121 deg C (250 deg F) or 3 hr At 121 deg C (250 deg F) plus 3 hr At 135 deg C (275 deg F) Full Cure Time, 30 min At 120 deg C Gel Time, 90 Shore D (ASTM D2240) Hardness, 9800 psi Tensile Strength, 18000 - 28000 CP At 25 deg C Resin ASTM D2196, 100 CP At 65 deg C (Mixed Resin) ASTM D2196 Viscosity - Part-A, 100 - 500 CP At 25 deg C Catalyst Viscosity - Part-B.

     

  • Von Roll/John C Dolph LC-705 Insulating Lacquer Varnish

    Multiple item options available
    Mfr ID: LC-705
    Von Roll/John C Dolph LC-705 Insulating Lacquer Varnish, 1500 V/Mil (Dry), 800 V/Mil (Wet) Dielectric Strength, 10 - 30 min Dry Time, 105 deg C Temperature Rating.

    In Stock

  • Elantas PDG 10007050485LB Pedigree® Alkyd Water-Borne Varnish, 485 lb/55 gal

    ID: 10007050485LB
    Mfr ID: 10007050485LB
    Elantas PDG Pedigree® Alkyd, Water-Borne Varnish, Heat Cure Type, 3600 V/Mil (Dry), 3300 V/Mil (Wet) Dielectric Strength, >94 deg C Flash Point, Liquid Form, 1600 - 2500 CP At 25 deg C Viscosity.

     

  • Elantas PDG Pedigree® 6180 UP Polyester Resin

    Multiple item options available
    Mfr ID: Pedigree® 6180
    Elantas PDG Pedigree® 6180 UP Polyester Resin, 3840 V/Mil Dry, 3420 Wet Dielectric Strength, 30 deg C Flash Point, 5 - 10 hr At 105 deg C to 121 deg C Full Cure Time.

     

  • Elantas PDG Pedigree® PED-961 Quick Cure Insulating Varnish

    Multiple item options available
    Mfr ID: Pedigree® PED-961
    Elantas PDG Pedigree® Quick Cure Insulating Varnish, 3900 V/Mil (Dry), 2700 V/Mil (Wet) Dielectric Strength, 18 deg C Flash Point, 2 hr At 150 deg C Full Cure Time, 150 - 250 CP At 25 deg C Viscosity.

    In Stock

  • Von Roll Permafil® 712C Solventless Polyester Resin

    Multiple item options available
    Mfr ID: Permafil® 712C
    VRI 712 is a high flash point solventless polyester varnish. This varnish is suitable for use in dip tanks. VRI 712 has a true "closed cup" flash point (Pensky-Martens) in excess of 200 deg F (93 deg C). VRI 712 varnish offers excellent catalyzed tank stability.

    In Stock

  • Star Wire Banding Epoxy With Reactor, 5 gal

    ID: START2237AKIT
    Mfr ID: START2237AKIT
    Star Wire Banding Epoxy With Reactor, Epoxy Base Type.

    In Stock

  • Von Roll Thinner, 1 gal

    ID: VRI1500G
    Mfr ID: VRI1500G
    Von Roll Thinner, Liquid Form.

     

  • Von Roll VSR-1118 Reducer

    Multiple item options available
    Mfr ID: VSR-1118
    Von Roll VSR-1118 Reducer, Liquid Form.

     

  • Von Roll 111-442 Varnish

    Multiple item options available
    Mfr ID: 111-442
    Von Roll 111-442 Varnish.

     

  • Glyptal 1276 Adhesive Lacquer Cement

    Multiple item options available
    Mfr ID: 1276
    Mfr: Glyptal
    Glyptal 1276 Adhesive Lacquer Cement.

    In Stock

  • Von Roll 3332 Peroxide Catalyst

    Multiple item options available
    Mfr ID: 3332
    Von Roll 3332 Peroxide Catalyst.

    In Stock

  • Elantas PDG 5180DRUM Polyester Resin With UV Tracer, 500 lb

    ID: 5180DRUM
    Mfr ID: 5180DRUM
    Elantas PDG 5180DRUM Polyester Resin With UV Tracer.

    In Stock

  • Elantas PDG 60-60-VT Precatalyzed Polyester Resin

    Multiple item options available
    Mfr ID: 60-60-VT
    Elantas PDG 60-60-VT Precatalyzed Polyester Resin, 1.0689 g/cm3 (25 deg C (77 deg F)) Density, 52 deg C Flash Point, 0.954 Specific Gravity, 95 cSt (95 mm2/sec) At 40 C Viscosity.

     

  • Elantas PDG 674 Alkyd Resin, 15 oz, Green

    ID: E67415OZ
    Mfr ID: E67415OZ
    Elantas PDG 674 Alkyd Resin.

    In Stock

    • 1(current)
    • 2
    • 3