text.skipToContent text.skipToNavigation

Conductive Adhesives & Coatings

Electrically and thermally conductive adhesives, for electrical and mechanical bonds, providing reliable interconnection of parts and managing heat in electronic components.
Displaying 1 - 17 of 17 products found
  • Parker 50-01-0360-0020 Cho-Bond® Two-Part Conductive Adhesive, 1 pt Aluminum Can Kit, Light Gray

    ID: CHOBOND03600020
    Mfr ID: 50-01-0360-0020
    Cho-Bond 360-20 is a two-component, silver plated copper filled conductive epoxy adhesive designed for applications where a strong, conductive electrical bond must be achieved. The silver copper filler of Cho-Bond 360-20 provides a cost effective alternative to pure silver filled conductive epoxies in applications where moderate conductivity is acceptable.

     

  • ITW Chemtronics CW2400 CircuitWorks® Conductive Epoxy, 0.25 oz Syringe, Gray/Silver-Gray

    ID: CW2400
    Mfr ID: CW2400
    CircuitWorks conductive epoxy is a two-part, silver epoxy used in prototype, repair and general conductive bonding applications. It features strong mechanical bonds, excellent electrical conductivity and quick room temperature curing. CircuitWorks conductive epoxy bonds aggressively to a wide variety of materials.

    In Stock

  • Von Roll 3040 E-Kote® Conductive Acrylic Coating, 3 oz Kit, Silver

    ID: EKOTE30403OZ
    Mfr ID: 3040
    E-Kote 3040 is a silver-filled electrically conductive synthetic coating. This material exhibits excellent conductivity and good environmental resistance. It sets up by solvent evaporation to form a hard, tough, flexible film with good adhesion to most surfaces. E-Kote 3040 is recommended in applications where solderability is NOT required.

     

  • Von Roll 3068 E-Kote® Conductive Epoxy, 3 oz Kit, Silver

    ID: EKOTE30683OZ
    Mfr ID: 3068
    E-Kote 3068 is a silver-filled epoxy coating, which exhibits low electrical resistance and excellent adhesion to a variety of substrates such as glass, plastics, metal and ceramics. E-Kote 3068 requires the addition of hardener to cure. This will cure at room temperature. However, the application of heat will accelerate and shorten the cure time.

     

  • Von Roll 3072 E-Kote® Conductive Graphite Coating, 1 gal, Gray

    ID: EKOTE3072G
    Mfr ID: 3072
    E-Kote 3072 is an economical graphite acrylic conductive coating ideal for use when only grounding properties or controlling ESD are needed.

     

  • Von Roll 3012 E-Solder® Conductive Adhesive, 2 oz Bottle, Silver

    ID: ESOLDER30122OZ
    Mfr ID: 3012
    Von Roll 3012 E-Solder Conductive Adhesive.

     

  • Von Roll 3025 E-Solder® Conductive Adhesive, 2 oz Kit, Silver

    ID: ESOLDER30252OZ
    Mfr ID: 3025
    E-Solder 3025 is an epoxy silver paste recommended for applications requiring low electrical resistance and good adhesive properties. E-Solder 3025 requires the addition of Hardener No. 18 to harden and cure. E-Solder 3025 may be cured at room temperature, however the application of heat will accelerate and shorten the cure time.

     

  • Loctite 5421 Conductive Adhesive, 50mL Cartridge, Tan

    ID: LOC32728
    Mfr ID: 5421
    Loctite 5421 is an RTV silicone that provides EMI/RFI shielding on electronic device enclosures.

     

  • Parker 50-00-0360-0208 Cho-Bond® Conductive Adhesive, 3 oz Kit, Gray

    ID: CHOBOND0360
    Mfr ID: 50-00-0360-0208
    Cho-Bond adhesive/sealant uses a filler blend of pure silver and silver-plated-copper particles to produce superior shielding performance without requiring contact pressure, making it an ideal fillet seal.

     

  • Parker 50-02-0584-0029 Cho-Bond® Two-Part Conductive Adhesive, 2.5g Pack, Silver Gray

    ID: CHOBOND058415
    Mfr ID: 50-02-0584-0029
    Cho-Bond 584-29 is a two-component, silver filled conductive epoxy adhesive system designed for applications where a strong, highly conductive electrical bond must be achieved. Cho-Bond 584-29 is recommended for relatively small bond lines (less than 0.010 Inch (0.25 mm)), but can be used for larger bond lines in applications where vibration or potential for cracking is not an issue.

    In Stock

  • Parker 50-01-1030-0000 Cho-Bond® One-Part Conductive Adhesive, 1 lb Cartridge, Gray

    ID: CHOBOND103010
    Mfr ID: 50-01-1030-0000
    Cho-Bond 1030 is a silver plated copper filled, one-component conductive silicone designed for applications where a flexible, strong, conductive electrical bond must be achieved. Cho-Bond 1030 greatly simplifies the problem of bonding conductive silicone EMI gaskets to metal substrates. It is formulated for relatively small bond lines (less than 0.01 Inch and should not be used as an EMI caulk where bond lines are greater than 0.1 Inch (0.25 mm).

     

  • Von Roll 3022 E-Solder® Conductive Adhesive, 2 oz Kit, Silver

    ID: ESOLDER30222OZ
    Mfr ID: 3022
    E-Solder 3022 is an epoxy silver paste recommended for applications requiring low electrical resistance and good adhesive properties. E-Solder 3022 requires the addition of Hardener No. 18 to harden and cure. E-Solder 3022 may be cured at room temperature, however the application of heat will accelerate and shorten the cure time.

    In Stock

  • Von Roll 3021 E-Solder® Conductive Adhesive, 2 oz Kit, Silver

    ID: ESOLDER30212OZ
    Mfr ID: 3021
    E-Solder 3021 is an epoxy silver composition recommended for applications requiring high electrical conductivity and good adhesive properties. E-Solder is supplied as a two-component system consisting of Part A and Part B. Mixing the two-parts in equal proportions results in a fast setting, tough, thermoset, highly conductive plastic.

    In Stock

  • Von Roll 3030 E-Kote® Synthetic Conductive Acrylic Coating

    Multiple item options available
    Mfr ID: VRI-3030
    E-Kote 3030 is a silver-filled electrically conductive synthetic coating with a thermoplastic base. It sets up by solvent evaporation to form a hard, tough film which may be soldered by using conventional tin-lead solders. E-Kote 3030 may be applied by dipping, brushing or silk-screening.

    In Stock

  • Von Roll 3063ALC E-Kote® Conductive Acrylic Coating, 1 gal Can, Black

    ID: EKOTE3063ALCG
    Mfr ID: 3063ALC
    E-Kote 3063 is highly conductive, all-purpose economical nickel coating and is ideal for use in applications where conductivity and attenuation stability are required when shielding EMI/RFI.

     

  • Dow Corning 1-4173 One-Part Thermally Conductive Adhesive

    Multiple item options available
    Mfr ID: 1-4173
    Dow Corning 1-4173 heat-cure, thermally conductive adhesives produce no by-products in the cure process, allowing their use in deep section and complete confinement. These adhesives will develop good, primerless adhesion to a variety of common substrates including metals, ceramics, epoxy laminate boards, reactive materials and filled plastics.

     

  • Dow Corning Q1-9226 Two-Part Thermally Conductive Adhesive, 2kg Kit, White

    ID: DCQ1-9226X2KG
    Mfr ID: Q1-9226X2KG
    Dow Corning Q1-9226 heat-cure, thermally conductive adhesives produce no by-products in the cure process, allowing their use in deep section and complete confinement. These adhesives will develop good, primerless adhesion to a variety of common substrates including metals, ceramics, epoxy laminate boards, reactive materials and filled plastics. Electronic devices are continually designed to deliver higher performance.