text.skipToContent text.skipToNavigation

Resins

Resins are an important factor in ensuring the protection of your wire windings and coils. Resins are exceptionally important for inductor coils and they are often packed so tightly that the coils can rub against one another and cause internal damage. Electrical Resin offers protection from mechanical damage, vibration dampening, moisture prevention, and heat prevention.

EIS supplies Resins from many different top suppliers in an assortment of forms, insulation types, and mixing ratios to meet the demands of any application.

  • 1(current)
  • 2
  • 3
Displaying 1 - 21 of 339 products found
  • Elantas PDG 80IP-545M Annealing Coreplate, 50 lb/5 gal, Red

    ID: 80IP545M50LB
    Mfr ID: 80IP545M50LB
    Sterling 80IP-545M red annealing coreplate was designed as a water reducible electrical insulating coating for application to electrical sheet steel which, after cutting, is stamped and then annealed to relieve cutting stresses. After the annealing operation the coating is a good separator and retains its electrical insulating properties.

     

  • Von Roll/John C Dolph Dolphon® CB-1057 Epoxy Buttering Resin Reactor Kit

    Multiple item options available
    Mfr ID: Dolphon® CB-1057
    Von Roll/John C Dolph Dolphon® CB-1057 Epoxy Buttering Resin Reactor Kit, Epoxy Base Type, Room Temperature Cure Type, 430 V/Mil Dielectric Strength, 70 - 75 Shore D Hardness, 8100 psi Tensile Strength, 8 x 10^-4 Cal/sec/cm^2/deg C/cm Thermal Conductivity.

    In Stock

  • Von Roll/John C Dolph Dolphon® CB-1128-B Two-Part Flexible Motor Compound

    Multiple item options available
    Mfr ID: Dolphon® CB-1128-B
    Von Roll/John C Dolph Dolphon® CB-1128-B Two-Part Flexible Motor Compound, Room Temperature Cure Type, 8.8 - 9.0 lb/gal At 77 deg F (25 deg C) Density, 665 V/Mil Dielectric Strength, 2 - 4 hr At 77 deg F Full Cure Time, 45 Shore A At 70 deg F Hardness, 100:6 By Weight Mixing Ratio, 130 deg C Temperature Rating, 1260 psi Tensile Strength, 12.2 x 10^-4 Cal/sec/cm^2/deg C/cm Thermal Conductivity, 100000 cps At 80 deg F, 10 rpm Viscosity.

     

  • Von Roll/John C Dolph Dolphon® CC-1103 Solventless Resin, 55 gal

    ID: DOLCC110355G
    Mfr ID: DOLCC110355G
    Filled solventless polyester resin, this product features qualities such as 24 lbs. bond strength at 150 deg F on helical coils, similar to CC-1105. This product has film build of 1.4 - 1.7 Mil and increased thermal conductivity.

     

  • Von Roll/John C Dolph Dolphon® XL-2102 Solventless Polyester Dip And VPI Resin

    Multiple item options available
    Mfr ID: Dolphon® XL-2102
    Von Roll/John C Dolph Dolphon® XL-2102 Solventless Polyester Dip And VPI Resin, 3250 V/Mil (Dry), 2890 V/Mil (Wet) Dielectric Strength, >200 deg F Flash Point, 8 - 13 min At 257 deg F (125 deg C), ASTM D 3056 Gel Time, 350 - 650 cps At 77 deg F (25 deg C), ASTM D2196 Viscosity.

    In Stock

  • Elantas PDG Elan-Cast® ERX 023A Two-Component Epoxy Resin, 519 - 600 lb/45.45 gal (Part-A), Black/Amber

    ID: RANERX023ADRUM
    Mfr ID: RANERX023ADRUM
    Elantas PDG Elan-Cast® ERX 023A Two-Component Epoxy Resin, Epoxy Base Type, Black - Part-A, Amber - Part-B, 1.5760 g/cm3 (77 deg F (25 deg C)) Resin, 1.6552 g/cm3 At 25 deg C (77 deg F) (1.013 hPa) Hardener Density, 430 V/Mil At 25 deg C/77 deg C - 70 Mil (ASTM D149), 360 V/Mil At 25 deg C/77 deg C - 70 Mil (ASTM D149) Dielectric Strength, 4% At 25 deg C/77 deg F (ASTM D638) Elongation, >94 deg C (ASTM D93) Flash Point, 24 hr At 25 deg C/77 deg F Plus 15 hr At 60 deg C/140 deg F Full Cure Time, 30 - 65 min At 25 deg C/77 deg F Gel Time, 70 Shore D Hardness, 100 (Parts By Weight And Volume) Resin, 106 (Parts By Weight) 100 (Parts By Volume) Hardener Mixing Ratio, 3900 psi (ASTM D638) Tensile Strength, 0.7 W/mK Thermal Conductivity, 17000 - 28000 CP At 25 deg C/77 deg F Viscosity, 20000 - 25000 CP At 25 deg C/77 deg F Viscosity - Part-A, 15000 - 30000 CP At 25 deg C/77 deg F Viscosity - Part-B.

    In Stock

  • Elantas PDG Epoxylite® E6107 Two-Component High-Temperature Impregnating Epoxy Resin

    Multiple item options available
    Mfr ID: Epoxylite® E6107
    Elantas PDG Epoxylite® E6107 Two-Component, High-Temperature Impregnating Epoxy Resin, Epoxy Base Type, 1.2040 g/cm3 (68 deg F (20 deg C)) Density, 480 V/Mil Dielectric Strength, 143 deg C (ASTM D93 Part A Resin), > 94 deg C (ASTM D93 Part B Catalyst) Flash Point, 6 - 8 hr At 121 deg C (250 deg F) or 3 hr At 121 deg C (250 deg F) plus 3 hr At 135 deg C (275 deg F) Full Cure Time, 30 min At 120 deg C Gel Time, 90 Shore D (ASTM D2240) Hardness, 9800 psi Tensile Strength, 18000 - 28000 CP At 25 deg C Resin ASTM D2196, 100 CP At 65 deg C (Mixed Resin) ASTM D2196 Viscosity - Part-A, 100 - 500 CP At 25 deg C Catalyst Viscosity - Part-B.

     

  • 3M Scotchcast™ 5555-22G Coil Insulating Epoxy Powder Electrical Resin, 44 lb, Green

    ID: 3MR555522G44LB
    Mfr ID: 3MR555522G44LB
    Electrical resin 5555 is manufactured by a fusion blend process, insuring that each individual particle of powder contains all the components necessary to effect a complete cure and attain stated performance properties. Resin 5555 can be applied via cold electrostatic fluid bed, hot venturi spray or hot fluid bed dip. Resin 5555 has two gel times in order to accommodate those applications that need slightly higher flow, or for application equipment that requires rapid curing.

    In Stock

  • Star Wire Banding Epoxy With Reactor, 5 gal

    ID: START2237AKIT
    Mfr ID: START2237AKIT
    Star Wire Banding Epoxy With Reactor, Epoxy Base Type.

    In Stock

  • Elantas PDG Pedigree® 6180 UP Polyester Resin

    Multiple item options available
    Mfr ID: Pedigree® 6180
    Elantas PDG Pedigree® 6180 UP Polyester Resin, 3840 V/Mil Dry, 3420 Wet Dielectric Strength, 30 deg C Flash Point, 5 - 10 hr At 105 deg C to 121 deg C Full Cure Time.

     

  • Von Roll 74100 Compound Resin, 1 qt

    ID: VRI74100Q
    Mfr ID: VRI74100Q
    Von Roll 74100 Compound Resin.

     

  • Von Roll/John C Dolph Dolphon® CB-1069 Epoxy Potting And Casting Resin, 12 lb/1 gal, Black

    ID: DOLCB106912LB
    Mfr ID: DOLCB106912LB
    Von Roll/John C Dolph Dolphon® CB-1069 is a general purpose, high thermal conductivity, black epoxy casting and potting resin for use in all types of electrical and electronic assemblies.

    In Stock

  • Von Roll/John C Dolph Dolphon® CB-1054-B Two-Part Epoxy Resin Reactor, 10 lb/1 gal, Cream

    ID: DOLCB1054BG
    Mfr ID: DOLCB1054BG
    Von Roll/John C Dolph Dolphon® CB-1054-B Two-Part Epoxy Resin Reactor, Epoxy Base Type, Room Temperature Cure Type, 430 V/Mil (1/8 Inch Specimen) Dielectric Strength, 16800 psi (ASTM D790) Flexural Strength, 8 - 12 hr At 225 deg F or 6 - 8 hr At 255 deg F or 3 - 5 hr At 275 deg F Full Cure Time, 60 Shore D Hardness, 1.8 cps At 70 deg F Specific Gravity, Class F Temperature Rating, 1.25 x 10³ Cal/sec/cm^2/deg C/cm Thermal Conductivity, 5400 CP At 77 deg F (25 deg C) Viscosity.

     

  • Von Roll/John C Dolph Dolphon® CC-1089 Epoxy Flow-On Resin Reactor Kit

    Multiple item options available
    Mfr ID: Dolphon® CC-1089
    Von Roll/John C Dolph Dolphon® CC-1089 Epoxy Flow-On Resin Reactor Kit, Epoxy Base Type, 450 V/Mil Dielectric Strength, 70 Shore D Hardness, 7500 psi Tensile Strength, 4.9 x 10^-4 Cal/sec/cm^2/deg C/cm Thermal Conductivity.

     

  • Von Roll/John C Dolph Dolphon® CC-1024A Potting And Casting Epoxy Resin

    Multiple item options available
    Mfr ID: Dolphon® CC-1024A
    Von Roll/John C Dolph Dolphon® CC-1024A Potting And Casting Epoxy Resin, Epoxy Base Type, Room Temperature Cure Type, 9.2 - 9.6 lb/gal At 77 deg F (25 deg C) Density, 500 V/Mil Dielectric Strength, 2.3% (ASTM D-638) Elongation, 15000 psi (ASTM D790) Flexural Strength, 30 - 50 min At 132 deg F Gel Time, 75 Shore D For 24 hours Hardness, 100 (By Weight) Mixing Ratio, 9000 psi Tensile Strength, 1.16 BTU/HR/ft²/Inch/deg F Thermal Conductivity.

    In Stock

  • Von Roll/John C Dolph Dolphon® CC-1105-HTC Solventless Polyester Resin

    Multiple item options available
    Mfr ID: Dolphon® CC-1105-HTC
    Von Roll/John C Dolph Dolphon® CC-1105-HTC Solventless Polyester Resin, 10.4 - 10.8 lb/gal At 77 deg F (25 deg C) Density, 3000 V/Mil Dielectric Strength, >200 deg F Flash Point, 10 - 15 min At 275 deg F Gel Time, 0.97 BTU/HR/ft²/Inch/deg F Thermal Conductivity, 900 -1500 cps At 10 rpm 77 deg F (25 deg C), 1900 - 4100 cps At 10 rpm 77 deg F (25 deg C) Viscosity.

    In Stock

  • Von Roll/John C Dolph Dolphon® CC-1115 Solventless VPI Epoxy Resin

    Multiple item options available
    Mfr ID: Dolphon® CC-1115
    Von Roll/John C Dolph Dolphon® CC-1115 Solventless VPI Epoxy Resin, Epoxy Base Type, 2,200 V/Mil (ASTM D 115) Dielectric Strength, >200 deg F Flash Point, 15 - 23 min At 285 deg F (140 deg C), ASTM D 3056 Gel Time, 80 - 90 Shore D (ASTM D 2240) Hardness, 11000 – 17000 cps (At 1 rpm 77 deg F (25 deg C), ASTM D1475), 4000 - 6000 cps (At 10 rpm 77 deg F (25 deg C), ASTM D1475) Viscosity.

    In Stock

  • Von Roll/John C Dolph Dolphon® CC-1105-OPT Solventless One Part Trickle Resin

    Multiple item options available
    Mfr ID: Dolphon® CC-1105-OPT
    Von Roll/John C Dolph Dolphon® CC-1105-OPT Solventless One Part Trickle Resin, 9.6 - 10.0 lb/gal At 77 deg F (25 deg C) Density, 5,300 V/Mil Dielectric Strength, >200 deg F Flash Point, 14 - 18 min At 212 deg F (100 deg C) Gel Time, Mild to Odorless Odor/Scent, 1.2 Specific Gravity, 0.53 BTU/HR/ft²/Inch/deg F Thermal Conductivity, 400 - 800 cps (Brookfield Model RVT #1 Spindle At 77 deg F (25 deg C), 10 rpm) Viscosity.

     

  • Von Roll/John C Dolph Dolphon® CC-1118-LV Solventless Resin

    Multiple item options available
    Mfr ID: Dolphon® CC-1118-LV
    Von Roll Dolphon® CC-1118-LV Solventless Resin, Clear.

     

  • Von Roll/John C Dolph Dolphon® CC-1141 Solventless Polyester Resin

    Multiple item options available
    Mfr ID: Dolphon® CC-1141
    CC-1141 is designed for both VPI and dip and bake applications, it offers the advantages of both epoxy and polyester resins. Its unique proprietary formulation allow for maximum stability and versatility.

     

  • Von Roll/John C Dolph Dolphon® CC-1305 Solventless Polyester Resin

    Multiple item options available
    Mfr ID: Dolphon® CC-1305
    Von Roll/John C Dolph Dolphon® CC-1305 Solventless Polyester Resin, 9.2 - 9.6 lb/gal At 77 deg F (25 deg C) Density, 3500 V/Mil Dielectric Strength, >200 deg F Flash Point, 110 - 150 min At 212 deg F, 40 - 55 min At 230 deg F Gel Time, 2.75 BTU/HR/ft²/Inch/deg F Thermal Conductivity, 1000 - 2500 cps At 77 deg F Viscosity.

    In Stock

    • 1(current)
    • 2
    • 3