text.skipToContent text.skipToNavigation

Elantas PDG Sterling® E300-HB Single-Component Thixotropic Epoxy Resin, 50 lb/5 gal

ID: PDGE300HB50LB Mfr ID: PDGE300HB50LB
Manufactured by: ELANTAS PDG, Inc.
Elantas PDG Sterling® E300-HB Single-Component Thixotropic Epoxy Resin, Epoxy Base Type, 1.4953 g/cm3 (77 deg F (25 deg C)) Density, 1500 V/Mil (ASTM D149 - 4 Mil), 1300 V/Mil (ASTM D149 - 4 Mil After 24 hr in Water ) Dielectric Strength, >94 deg C (ASTM D93) Flash Point, 16 hr At 150 deg C/302 deg F Full Cure Time, 8 - 15 min At 150 deg C (302 deg F) Gel Time, 90 Shore D At 25 deg C/77 deg F Hardness, 500000 - 750000 CP At 25 deg C/77 deg F, 2 rpm, 140000 - 200000 CP At 25 deg C/77 deg F, 20 rpm Viscosity.
Special Handling Required



USD $16.89 / LB

Buy more and save

50-649 $16.89 / LB
650-1249 $14.22 / LB
1250+ $12.28 / LB

Check availability 

This item may be sold in units of 50.

  • Brand name :  Elantas Pdg
  • Trade Name :  Sterling®
  • Series :  Sterling® E300-HB
  • Item Name :  Thixotropic Epoxy Resin
  • Short Desc :  THERMOPOXY,THIXO,E 300 HB,50-LB/5-GAL PL
  • UNSPSC :  13111001

Sterling® E 300 HB thixo is a single-component, heat-cured, epoxy bonding resin.

WARNING

WARNING: California Proposition 65 - Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Performance Details
Full Cure Time 16 hr at 150 deg C/302 deg F 
Gel Time 8  min
Design & Construction
Base Type Epoxy 
Form Liquid 
General Features
Shelf Life 3 Months 
Type Single-Component 
Net Weight 12.3 - 12.7 lb/gal 
Environmental Condition
Flash Point 94  deg C
Electrical Properties
Dielectric Strength 1500  V/mil
Chemical Properties
Viscosity 500000  cP
Physical Properties
Hardness 90 Shore D at 25 deg C/77 deg F 
Container Size 50  lb
Container Type Pail 

Elantas PDG Sterling® E300-HB Single-Component Thixotropic Epoxy Resin, 50 lb/5 gal Brochure 

Elantas PDG Sterling® E300-HB Single-Component Thixotropic Epoxy Resin, 50 lb/5 gal Safety Data Sheet (SDS) 

Features :

  • Outstanding bond strength
  • Good chemical resistance
  • No catalyst required
  • Thixotropic for minimal run-off
  • Thermal ratings up to class 180
  • Mix thoroughly before use, warm resin to 30-40 deg C / 86-104 deg F, apply with stiff brush, spatula or notched spreader application methods
  • Store below 25 deg C / 77 deg F in a dry controlled environment out of direct sunlight
  • 150 deg C heat deflection temperature
  • 1.0 x 10^12 Ohm-cm at ASTM D257 - 25 deg C / 77 deg F, 2.0 x 10^11 Ohm-cm at ASTM D257 - 100 deg C / 212 deg F volume resistivity
  • 72 Pounds at 25 deg C / 77 deg F, 30 Pounds at 150 deg C / 302 deg F helical coil bond strength (ASTM D2519 over MW 35)
  • Secondary insulation
  • Container Size: 50 lb/5 gal
  • Dielectric Strength: 1500 V/Mil (ASTM D149 - 4 Mil), 1300 V/Mil (ASTM D149 - 4 Mil After 24 hr in Water )
  • Flash Point: >94 deg C (ASTM D93)
  • Viscosity: 500000 - 750000 CP at 25 deg C/77 deg F, 2 rpm, 140000 - 200000 CP at 25 deg C/77 deg F, 20 rpm
  • Density: 1.4953 g/cm3 (77 deg F (25 deg C))
  • Gel Time: 8 - 15 min
  • Viscosity: 500000 - 750000 cP

Applications :

  • Wet-Winding of Rotating or Stationary Field Coils, Impregnation, Bonding and Sealing of Electrical and Mechanical Components