text.skipToContent text.skipToNavigation

Banding Tapes

Displaying 1 - 17 of 17 products found
  • Von Roll Poly Glas® 76841 Polyester Banding Tape, 1/4" x 1000'

    ID: BAND768411/4
    Mfr ID: BAND768411/4
    Poly Glas banding tapes are B-staged resin bonded unidirectional glass or kevlar yarns utilized to band and fix parts of electrical devices to withstand the mechanical stress during operation. Typically used for banding of motor coils and transformer cores and coils. Polyglas tapes are banded according to specific conditions.

     

  • Von Roll Poly Glas® 76881 Polyester Banding Tape, 3/4" x 250 yd

    ID: BAND768813/4
    Mfr ID: BAND768813/4
    Poly Glas 76881 is an electrical grade, parallel glass banding tape, impregnated with an uncured, high temperature, modified epoxy varnish. The glass fibers used are specially treated to improve moisture resistance. During cure, resin flow fills voids and air spaces, producing a homogeneous laminate, with a smooth resin rich surface.

    In Stock

  • 3M EMB-45R Electrical Moisture Block, 3/4" x 100' x 45 Mil, Black

    ID: 3MABEMB45R
    Mfr ID: 80610456255
    EMB moisture block is supplied on a release liner and offered in standard sizes to accommodate different size wire bundles. EMB moisture block is compatible with typical wire insulation such as PVC, synthetic rubber and cross linked polyethylene. Easily installed, flame retardant.

     

  • Fibertek Res-I-Band Heat Shrinkable Mylar Banding Film

    Multiple item options available
    Mfr ID: Res-I-Band
    Mfr: Fibertek
    Res-I-Band banding film is a heat shrinkable polyester film specially designed for use with glass banding tapes to improve the finish and appearance on banded armatures and commutators. The pre-set and uniform shrinkage of Res-I-Band improves resin flow and provides a smooth finish on the glass band. It also minimizes build up of foreign matter thereby reducing the possibility of tracking. It enhances the performance, insulation integrity and the appearance of the glass bands on armatures and commutators. Res-I-Band provides an accurate and consistent 5% shrink factor yielding the ultimate in smooth surface banding.

     

  • Fibertek Res-I-Flex Flexible Sealable Armor Tape

    Multiple item options available
    Mfr ID: Res-I-Flex
    Mfr: Fibertek
    Fibertek Res-I-Flex is a B-staged, epoxy coated, woven polyester/glass tape which shrinks and fuses during the cure cycle to insure a tough, conformal moisture and chemical resistant dielectric seal for AC stators and DC armature coils.

    In Stock

  • Von Roll Poly Glas® 76843 Polyester Banding Tape

    Multiple item options available
    Mfr ID: 76843
    Poly Glas 76843 is an electrical grade, parallel glass banding tape, impregnated with an uncured, high temperature, modified polyester resin. The glass fibers used are specially treated to improve moisture resistance.

    In Stock

  • Fibertek Res-I-Straint Tadpole Edging Tape

    Multiple item options available
    Mfr ID: Res-I-Straint
    Mfr: Fibertek
    Fibertek Res-I-Straint assures your glass band of being the strongest, most secure and most accurate possible. Res-I-Straint tadpole edging tape is a nominal 5% resin impregnated and B staged edging tape used in conjunction with glass banding tape to provide a more uniform glass band. Hence, the diameter of the bead is proportionate to the thickness of the band.

     

  • Fibertek BANDB03224S3.5 Stator Cord Banding Tape, 3/8" x 350 yd Spool x 15 Mil, Translucent

    ID: BANDB03224S3.5
    Mfr ID: BANDB03224S3.5
    Mfr: Fibertek
    RES-I-GLAS stator cord is superior in tensile strength, durability, insulation value, ease of application and storage shelf life, due to the uncompromised use of highest grade raw materials and consistent manufacturing process. Constructed of high tensile electrical grade glass yarns laid parallel and bonded with fully catalyzed thermosetting resins. High tensile, high modulus, low elongation, high impact strength band. Eliminates insulation and creepage problems experienced with steel wire banding. Tape is supplied semi-cured (B-Stage) in a soft well balanced flat ribbon form and this assures that each yarn bears an equal share of the load.

     

  • HellermannTyton LOH1BK Polyamide 6.6 Banding Tape, Black

    ID: TYTLOH1BK
    Mfr ID: LOH1BK
    HellermannTyton Polyamide 6.6 Banding Tape.

     

  • Fibertek Res-I-Glas Type R Banding Tape

    Multiple item options available
    Mfr ID: Res-I-Glas-R
    Mfr: Fibertek
    RES-I-GLAS Type R is superior in tensile strength, durability, insulation value, ease of application and storage shelf life, due to the uncompromised use of highest grade raw materials and consistent manufacturing process. Constructed of high tensile electrical grade glass yarns laid parallel and bonded with fully catalyzed thermosetting resins. High tensile, high modulus, low elongation, high impact strength band. Eliminates insulation and creepage problems experienced with steel wire banding. Tape is supplied semi-cured (B-Stage) in a soft well balanced flat ribbon form and this assures that each yarn bears an equal share of the load.

    In Stock

  • Fibertek Res-I-Glas Type M Banding Tape

    Multiple item options available
    Mfr ID: Res-I-Glas-M
    Mfr: Fibertek
    RES-I-GLAS Type M is superior in tensile strength, durability, insulation value, ease of application and storage shelf life, due to the uncompromised use of highest grade raw materials and consistent manufacturing process. Constructed of high tensile electrical grade glass yarns laid parallel and bonded with fully catalyzed thermosetting resins. High tensile, high modulus, low elongation, high impact strength band. Eliminates insulation and creepage problems experienced with steel wire banding. Tape is supplied semi-cured (B-Stage) in a soft well balanced flat ribbon form and this assures that each yarn bears an equal share of the load.

    In Stock

  • Lectromat BANDEG Untreated Band Edge Guide Tape

    Multiple item options available
    Mfr ID: BANDEG
    Mfr: Lectromat
    Lectromat band edge guide tape.

    In Stock

  • Fibertek Res-I-Glas Type G Banding Tape

    Multiple item options available
    Mfr ID: Res-I-Glas-G
    Mfr: Fibertek
    RES-I-GLAS Type G is superior in tensile strength, durability, insulation value, ease of application and storage shelf life, due to the uncompromised use of highest grade raw materials and consistent manufacturing process. Constructed of high tensile electrical grade glass yarns laid parallel and bonded with fully catalyzed thermosetting resins. High tensile, high modulus, low elongation, high impact strength band. Eliminates insulation and creepage problems experienced with steel wire banding. Tape is supplied semi-cured (B-Stage) in a soft well balanced flat ribbon form and this assures that each yarn bears an equal share of the load.

    In Stock

  • Von Roll Poly Glas® 76830 Polyester Banding Tape

    Multiple item options available
    Mfr ID: 76830
    Poly Glas 76830 is an electrical grade, parallel glass banding tape, impregnated with an uncured, high temperature, modified polyester resin. During cure, resin flow fills voids and air spaces, producing a homogeneous laminate, with a smooth resin rich surface.

    In Stock

  • Von Roll Poly Glas® 76870 Polyester Banding Tape

    Multiple item options available
    Mfr ID: 76870
    Poly Glas 76870 is an electrical grade, moisture resistant, parallel glass banding tape, impregnated with an uncured, high temperature, modified polyester resin. During cure, resin flow fills voids and air spaces, producing a homogeneous laminate, with a smooth resin rich surface.

    In Stock

  • Fibertek Cotton Coilband Tape

    Multiple item options available
    Mfr ID: Band
    Mfr: Fibertek
    Coil band tapes are widely used in large scale transformer manufacturing and rewind shops as a tensile member replacement for woven cotton tapes and webbings. Coil band tapes are nonwoven, fabricated from unidirectional parallel cotton yarns and impregnated and bonded with an appropriate binder.

    In Stock

  • Fibertek Res-I-Glas Type F Banding Tape

    Multiple item options available
    Mfr ID: Res-I-Glas-F
    Mfr: Fibertek
    RES-I-GLAS Type F is superior in tensile strength, durability, insulation value, ease of application and storage shelf life, due to the uncompromised use of highest grade raw materials and consistent manufacturing process. Constructed of high tensile electrical grade glass yarns laid parallel and bonded with fully catalyzed thermosetting resins. High tensile, high modulus, low elongation, high impact strength band. Eliminates insulation and creepage problems experienced with steel wire banding. Tape is supplied semi-cured (B-Stage) in a soft well balanced flat ribbon form and this assures that each yarn bears an equal share of the load.

    In Stock