MFR #:117692
EIS #:PDGE4491G
MFR #:117692
EIS #:PDGE4491G
In Stock
Min Qty:1
|Qty Increment:1
more info
ELAN-Tron® and ELAN-Cast® resins are used for potting or casting of low voltage transformers. They provide environmental protection, minimize vibration and improve heat dissipation. Products are filled and sold by weight and may contain less than the nominal volume of the container. - ELAN-Tron® E 449 Resin / C 49 Hardener (sold separately) is a filled, 100%-solids, two-component epoxy resin system.
$36.69 / US pound
Min Qty:1
|Qty Increment:1
more info
ELAN-Tron® and ELAN-Cast® resins are used for potting or casting of low voltage transformers. They provide environmental protection, minimize vibration and improve heat dissipation. Products are filled and sold by weight and may contain less than the nominal volume of the container. - ELAN-Tron® E 449 Resin / C 49 Hardener (sold separately) is a filled, 100%-solids, two-component epoxy resin system.
- Attributes
- Features
- Documents
Attributes
General Information
Item NameEpoxy Resin
Trade NameElan-Tron®
SeriesElan-Tron® E449
General Features
Net Weight13.3 - 13.7 lb/gal Resin, 17.1 - 17.5 lb/gal Hardener
Shelf Life12 Months
TypeTwo-Component
Design & Construction
Base TypeEpoxy
Cure TypeRoom Temperature
FormLiquid
Performance Details
Full Cure Time6 hr
Chemical Properties
Mixing Ratio100 (Parts By Weight and Volume) Resin, 110 (Parts By Weight) 86 (Parts By Volume) Hardener
Viscosity - Part-B220000 cP
Physical Properties
Container Size12 lb
Hardness85 Shore D
Features
- Bonding of electrical components
- Repair of motor housings and castings
- Seam sealing in pressure processing equipment
- Repair of plastic, porcelain, tile and ceramics
- Mix resin and hardener in recommended ratio until homogeneous, apply with spatula, trowel or stiff brush application methods
- Store below 25 °C / 77 °F in a dry controlled environment out of direct sunlight
- 0.05% (ASTM D2566) linear shrinkage
- 0.14% (ASTM D570, 24 hours at 25 °C / 77 °F) water absorption
- 59 °C (By DSC) glass transition temperature
- 55 ppm / °C (below Tg) coefficient of thermal expansion
- 1.2% (24 hours at 180 °C / 356 °F) weight loss
- 4.6 x 10^10 Ohm-cm at 25 °C / 77 °F, 6.0 x 10^9 Ohm-cm at 100 °C / 212 °F volume resistivity
- 2.4 at 1 kHz - 25 °C / 77 °F, 3.5 at 1 kHz - 100 °C / 212 °F dielectric constant
- 0.01 at 1 kHz - 25 °C / 77 °F, 0.11 at 1 kHz - 100 °C / 212 °F dissipation factor
- Hardener is a filled, 100%-solids
- Container Size: 12 lb/1 gal
- Flash Point: >94 °C (ASTM D93) Resin, 62 °C (ASTM D93) Hardener
- Density: 1.6170 g/cm3 (77 °F (25 °C))
- Viscosity - Part-B: 220000 - 4200000 CP at 25 °C/77 °F (2 rpm), 90000 - 180000 CP at 25 °C/77 °F (20 rpm)
- Viscosity - Part-B: 220000 - 4200000 cP