Elantas PDG Elan-Tron® E697 Two-Component Epoxy Resin, 9 lb/1 gal
MFR #:117331
EIS #:PDGE697G
MFR #:117331
EIS #:PDGE697G
In Stock
Min Qty:1
|Qty Increment:1
Elantas PDG Elan-Tron® E697 Two-Component Epoxy Resin, Epoxy Base Type, Room Temperature Cure Type, 1.1382 g/cm3 (77 °F (25 °C)) Density, 550 V/Mil (ASTM D149 - 50 Mil), 550 V/Mil (ASTM D149 - 50 Mil After 24 hr in Water) Dielectric Strength, >94 °C (ASTM D93) Flash Point, 24 hr At 25 °C/77 °F Full Cure Time, 1 - 2 min At 25 °C/77 °F-250g Gel Time, 80 Shore D At 25 °C/77 °F Hardness, 100 (Parts By Weight And Volume) Resin, 50 (Parts By Weight) 58 (Parts By Volume) Hardener Mixing Ratio, 15000 - 25000 CP At 2 rpm 25 °C/77 °F, 4000 - 6000 CP At 20 rpm 25 °C/77 °F Viscosity - Part-A, 33000 - 63000 CP At 2 rpm 25 °C/77 °F, 6500 - 12500 CP At 20 rpm 25 °C/77 °F Viscosity - Part-B. - ELAN-Tron® E 697/C 126 is a two-component, high-solids epoxy resin system.
$121.65 / US pound
Min Qty:1
|Qty Increment:1
Elantas PDG Elan-Tron® E697 Two-Component Epoxy Resin, Epoxy Base Type, Room Temperature Cure Type, 1.1382 g/cm3 (77 °F (25 °C)) Density, 550 V/Mil (ASTM D149 - 50 Mil), 550 V/Mil (ASTM D149 - 50 Mil After 24 hr in Water) Dielectric Strength, >94 °C (ASTM D93) Flash Point, 24 hr At 25 °C/77 °F Full Cure Time, 1 - 2 min At 25 °C/77 °F-250g Gel Time, 80 Shore D At 25 °C/77 °F Hardness, 100 (Parts By Weight And Volume) Resin, 50 (Parts By Weight) 58 (Parts By Volume) Hardener Mixing Ratio, 15000 - 25000 CP At 2 rpm 25 °C/77 °F, 4000 - 6000 CP At 20 rpm 25 °C/77 °F Viscosity - Part-A, 33000 - 63000 CP At 2 rpm 25 °C/77 °F, 6500 - 12500 CP At 20 rpm 25 °C/77 °F Viscosity - Part-B. - ELAN-Tron® E 697/C 126 is a two-component, high-solids epoxy resin system.
- Attributes
- Features
- Applications
- Documents
Attributes
General Information
Item NameEpoxy Resin
Trade NameElan-Tron®
SeriesElan-Tron® E697
General Features
Net Weight9.4 - 9.7 lb/gal Resin, 8.1 - 8.4 lb/gal Hardener
Shelf Life12 Months
TypeTwo-Component
Design & Construction
Base TypeEpoxy
Cure TypeRoom Temperature
FormLiquid
Performance Details
Full Cure Time24 hr at 25 °C/77 °F
Gel Time1 min
Technical Details
Flash Point94 °C
Chemical Properties
Viscosity - Part-A15000 cP
Viscosity - Part-B33000 cP
Mixing Ratio100 (Parts By Weight and Volume) Resin, 50 (Parts By Weight) 58 (Parts By Volume) Hardener
Electrical Properties
Dielectric Strength550 V/mil
Physical Properties
Container Size9 lb
Container TypeCan
Hardness80 Shore D at 25 °C/77 °F
Features
- Room temperature or low heat cure
- Resistant to chemicals and moisture
- High solids to provide heavy build
- Thixotropic for low run-off
- Long pot life
- Dip, brush application methods
- Store below 25 °C / 77 °F in a dry controlled environment out of direct sunlight
- Non-volatiles: > 96% (calculated)
- 54 °C (TMA) glass transition temperature
- 0.03 at 1 kHz - 25 °C / 77 °F, 0.07 at 1 kHz - 50 °C / 122 °F, 0.50 at 1 kHz - 100 °C / 212 °F dissipation factor (ASTM D150)
- 3.2 at 1 kHz - 25 °C / 77 °F, 3.6 at 1 kHz - 50 °C / 122 °F, 7.7 at 1 kHz - 100 °C / 212 °F dielectric constant (ASTM D150)
- 1.5 x 10^14 ohm-cm at 25 °C / 77 °F volume resistivity
- Container Size: 9 lb/1 gal
- Dielectric Strength: 550 V/Mil (ASTM D149 - 50 Mil), 550 V/Mil (ASTM D149 - 50 Mil After 24 hr in Water)
- Flash Point: >94 °C (ASTM D93)
- Density: 1.1382 g/cm3 (77 °F (25 °C))
- Viscosity - Part-B: 33000 - 63000 CP at 2 rpm 25 °C/77 °F, 6500 - 12500 CP at 20 rpm 25 °C/77 °F
- Gel Time: 1 - 2 min
- Viscosity - Part-A: 15000 - 25000 cP
- Viscosity - Part-B: 33000 - 63000 cP
Applications
- Conformal Coating of Printed Circuit Boards and Other Electronic and Electrical Components