text.skipToContentdvywebrxdaexsbxaacuerzafvfx text.skipToNavigation

Elantas PDG Elan-Tron® E449 Two-Component Epoxy Resin, 12 lb/1 gal

ID: PDGE4491G Mfr ID: PDGE4491G
Manufactured by: ELANTAS PDG, Inc.
ELAN-Tron® and ELAN-Cast® resins are used for potting or casting of low voltage transformers. They provide environmental protection, minimize vibration and improve heat dissipation. Products are filled and sold by weight and may contain less than the nominal volume of the container.

USD $14.77 / LB

Buy more and save

12-155 $14.77 / LB
156-299 $12.44 / LB
300+ $10.74 / LB

In Stock

This item may be sold in units of 12.

  • Brand name :  Elantas PDG
  • Trade Name :  Elan-Tron®
  • Series :  Elan-Tron® E449
  • Item Name :  Epoxy Resin
  • Short Desc :  RESIN,EPOXY,FILLED,E 449,NAT 12-LB/1-GL
  • UNSPSC :  13111001

ELAN-Tron® E 449 Resin / C 49 Hardener (sold separately) is a filled, 100%-solids, two-component epoxy resin system.

Performance Details
Full Cure Time 6 hr 
Design & Construction
Base Type Epoxy 
Form Liquid 
Cure Type Room Temperature 
General Features
Shelf Life 12 Months 
Type Two-Component 
Net Weight 13.3 - 13.7 lb/gal Resin, 17.1 - 17.5 lb/gal Hardener 
Chemical Properties
Mixing Ratio 100 (Parts By Weight and Volume) Resin, 110 (Parts By Weight) 86 (Parts By Volume) Hardener 
Viscosity - Part-B 220000  cP
Physical Properties
Hardness 85 Shore D 
Container Size 12  lb

Elantas PDG Elan-Tron® E449 Two-Component Epoxy Resin, 12 lb/1 gal Brochure 

Elantas PDG Elan-Tron® E449 Two-Component Epoxy Resin, 12 lb/1 gal Safety Data Sheet (SDS) 

Features :

  • Bonding of electrical components
  • Repair of motor housings and castings
  • Seam sealing in pressure processing equipment
  • Repair of plastic, porcelain, tile and ceramics
  • Mix resin and hardener in recommended ratio until homogeneous, apply with spatula, trowel or stiff brush application methods
  • Store below 25 deg C / 77 deg F in a dry controlled environment out of direct sunlight
  • 0.05% (ASTM D2566) linear shrinkage
  • 0.14% (ASTM D570, 24 hours at 25 deg C / 77 deg F) water absorption
  • 59 deg C (By DSC) glass transition temperature
  • 55 ppm / deg C (below Tg) coefficient of thermal expansion
  • 1.2% (24 hours at 180 deg C / 356 deg F) weight loss
  • 4.6 x 10^10 Ohm-cm at 25 deg C / 77 deg F, 6.0 x 10^9 Ohm-cm at 100 deg C / 212 deg F volume resistivity
  • 2.4 at 1 kHz - 25 deg C / 77 deg F, 3.5 at 1 kHz - 100 deg C / 212 deg F dielectric constant
  • 0.01 at 1 kHz - 25 deg C / 77 deg F, 0.11 at 1 kHz - 100 deg C / 212 deg F dissipation factor
  • Hardener is a filled, 100%-solids
  • Container Size: 12 lb/1 gal
  • Flash Point: >94 deg C (ASTM D93) Resin, 62 deg C (ASTM D93) Hardener
  • Density: 1.6170 g/cm3 (77 deg F (25 deg C))
  • Viscosity - Part-B: 220000 - 4200000 CP at 25 deg C/77 deg F (2 rpm), 90000 - 180000 CP at 25 deg C/77 deg F (20 rpm)
  • Viscosity - Part-B: 220000 - 4200000 cP

Applications :